RE520953 — Phoenix L14-L15 ECU, John Deere TRACTOR 7030 SERIES
Original (stock) ECU file for the John Deere TRACTOR 7030 SERIES — 6800 190HP, Phoenix L14-L15 controller, hardware RE520953, software SW60145F. Unmodified factory read, usually within 3 hours after we confirm your ECU numbers.
Identification
| Vehicle | John Deere TRACTOR 7030 SERIES |
|---|---|
| Engine | 6800 190HP |
| Engine code | 6068HBM01 |
| ECU | Phoenix L14-L15 |
| Hardware number | RE520953 |
| Software number | SW60145F |
Compatibility
The same Phoenix L14-L15 with part number RE520953 is also fitted to these vehicles / engines in our archive:
| Vehicle | Engine | Software |
|---|---|---|
| John Deere TRACTOR 7030 SERIES (this page) | 6800 190HP · 6068HBM01 | SW60145F |
| John Deere 3520 | 9000 337HP · 6090HT804 | SW60265J |
| John Deere 3520 | 9000 341HP · 6090HT804 | SW60265G |
| John Deere 7630 | 6800 178HP · 6068HRW64 | SW60147A |
| John Deere 7730 | 6800 193HP · 6068HRW64 | SW60147C |
| John Deere 8130 | 9000 305HP · 6090HRW01 | SW60067F |
| John Deere 8230 | 9000 260HP · 6090HRW02 | SW60069K |
| John Deere 8330 | 9000 305HP · 6090HRW02 | SW60069J |
| John Deere 8430 | 9000 305HP · 6090HRW07 | SW60131D |
| John Deere 9680 | 9000 330HP · 6090HZ003 | SW60072M |
Cross references
Other software levels recorded on hardware RE520953:
What you get
A full, unmodified read of the Phoenix L14-L15 as it left the factory — the binary file produced by the original reading tool, no checksum or map changes. Use it to restore a stock calibration after a failed flash or a bad tune, or as the reference file for a tuning job. One read is stored for this identification.
| Archive reference | Driver | Damos / A2L |
|---|---|---|
| JHD_3349 | JHD_3349 | — |
Delivery: released to your account and announced by email usually within 3 hours, within 24 hours on business days, once we confirm the read matches the numbers on this page.
Questions about this file
Is this original file compatible with my John Deere TRACTOR 7030 SERIES?
Compare the hardware number (RE520953) and the software number (SW60145F) with the identification your tool reads from the ECU. The software number must match; a different hardware revision usually means a different file. Phoenix L-series controllers (John Deere) are identified by an RE part number such as RE532628 and an SW code; both are visible on the ECU label.
What exactly do I receive when I buy the Phoenix L14-L15 original for €25?
An unmodified factory read of the Phoenix L14-L15 (HW RE520953, SW SW60145F) as stored in our archive — a binary file in the format produced by the original reading tool. No modifications, no checksum changes: it is meant to restore the ECU to its stock calibration or to serve as a reference for a tuning job.
How and when is the file delivered?
After payment we confirm the read matches the numbers on this page and release it to your account, with an email notification — usually within 3 hours, within 24 hours on business days. If your ECU reports different numbers, tell us with the order and we look for the right file before delivering anything.
Can you also tune this Phoenix L14-L15 or remove EGR / AdBlue / DPF?
Yes — upload your own read through the tuning service and choose the modifications; every tuning job is quoted individually before you pay. The original on this page is useful as a backup before any modification is flashed.