1037511206 — Bosch EDC17CV41 ECU, New Holland T7
Original (stock) ECU file for the New Holland T7 — 6700 270HP, Bosch EDC17CV41 controller, software 1037511206. Unmodified factory read, usually within 3 hours after we confirm your ECU numbers.
Identification
| Vehicle | New Holland T7 |
|---|---|
| Engine | 6700 270HP |
| ECU | Bosch EDC17CV41 |
| Software number | 1037511206 |
Compatibility
The same Bosch EDC17CV41 with part number 1037511206 is also fitted to these vehicles / engines in our archive:
| Vehicle | Engine | Software |
|---|---|---|
| New Holland T7 (this page) | 6700 270HP | 1037511206 |
| New Holland CX | 8700 322HP | 1037511206 |
| New Holland T6 | 6700 180HP | 1037511206 |
| New Holland T8 | 8700 322HP | 1037511206 |
Cross references
Other hardware carrying software 1037511206:
What you get
A full, unmodified read of the Bosch EDC17CV41 as it left the factory — the binary file produced by the original reading tool, no checksum or map changes. Use it to restore a stock calibration after a failed flash or a bad tune, or as the reference file for a tuning job. 7 reads are stored for this identification; you receive the one matching your ECU identification.
| Archive reference | Driver | Damos / A2L |
|---|---|---|
| N67_DD8E | N67_DD8E | P_662_EDC17CV41_D30.HEX |
| NEW_2B32 | NEW_2B32 | P_662_EDC17CV41_D30 |
| NEW_6DDD | NEW_6DDD | P_662_EDC17CV41_D40.HEX |
| NEW_718C | NEW_718C | P_662_EDC17CV41_D30.HEX |
| NXXX206B | NXXX206B | P_662_EDC17CV41_D30.HEX |
| NXXX206E | NXXX206E | P_662_EDC17CV41_D40.HEX |
| NXXX9B33 | NXXX9B33 | P_662_EDC17CV41_D40.HEX |
Delivery: released to your account and announced by email usually within 3 hours, within 24 hours on business days, once we confirm the read matches the numbers on this page.
Questions about this file
Is this original file compatible with my New Holland T7?
Compare the software number (1037511206) with the identification your tool reads from the ECU. If your software number differs, tell us — we check whether a matching original exists. Bosch EDC17 controllers are identified by a 0281 hardware number and a 1037 software number. Many EDC17 variants on trucks are read in boot/bench mode rather than OBD, so make sure the tool identification matches these numbers before flashing.
What exactly do I receive when I buy the Bosch EDC17CV41 original for €25?
An unmodified factory read of the Bosch EDC17CV41 (SW 1037511206) as stored in our archive — a binary file in the format produced by the original reading tool, chosen among the 7 reads listed on this page after we match your identification. No modifications, no checksum changes: it is meant to restore the ECU to its stock calibration or to serve as a reference for a tuning job.
How and when is the file delivered?
After payment we confirm the read matches the numbers on this page and release it to your account, with an email notification — usually within 3 hours, within 24 hours on business days. If your ECU reports different numbers, tell us with the order and we look for the right file before delivering anything.
Can you also tune this Bosch EDC17CV41 or remove EGR / AdBlue / DPF?
Yes — upload your own read through the tuning service and choose the modifications; every tuning job is quoted individually before you pay. The original on this page is useful as a backup before any modification is flashed.